xcgf 发表于 2023-8-19 20:07:20

微星主板MPG Z390 GAMING PLUS 安装群晖不能识别硬盘

本帖最后由 xcgf 于 2023-8-20 18:42 编辑

请各位帮忙提供硬盘参数 让群晖能识别发现硬盘
tc@box:~$ sudo ./rploader.sh satamap now
Found SCSI HBAs, We need to install the SCSI modules
Don't run this as root.
Succesfully installed SCSI modules

Found SCSI/HBA "00:17.0 Intel Corporation SATA Controller (rev 10)" (2 drives)
lspci: -s: Invalid slot number
Found SCSI/HBA "" (0 drives)
lspci: -s: Invalid slot number
Found SCSI/HBA "" (0 drives)
lspci: -s: Invalid bus number
Found SCSI/HBA "" (0 drives)
lspci: -s: Invalid slot number
Found SCSI/HBA "" (0 drives)
lspci: -s: Invalid slot number
Found SCSI/HBA "" (0 drives)
lspci: -s: Invalid slot number
Found SCSI/HBA "" (0 drives)
lspci: -s: Invalid slot number
Found SCSI/HBA "" (0 drives)
lspci: -s: Invalid slot number
Found SCSI/HBA "" (0 drives)
lspci: -s: Invalid slot number
Found SCSI/HBA "" (0 drives)
lspci: -s: Invalid slot number
Found SCSI/HBA "" (0 drives)
lspci: -s: Invalid slot number
Found SCSI/HBA "" (0 drives)

Computed settings:
SataPortMap=1
DiskIdxMap=00

Should i update the user_config.json with these values ? y
Done.
tc@box:~$ dmesg | grep SATA 注意大写
[ 0.351985] ahci 0000:00:17.0: AHCI 0001.0301 32 slots 6 ports 6 Gbps 0x3f impl SATA mode
[ 0.604996] ata1: SATA max UDMA/133 abar m2048@0x90022000 port 0x90022100 irq 120
[ 0.604999] ata2: SATA max UDMA/133 abar m2048@0x90022000 port 0x90022180 irq 120
[ 0.605000] ata3: SATA max UDMA/133 abar m2048@0x90022000 port 0x90022200 irq 120
[ 0.605001] ata4: SATA max UDMA/133 abar m2048@0x90022000 port 0x90022280 irq 120
[ 0.605003] ata5: SATA max UDMA/133 abar m2048@0x90022000 port 0x90022300 irq 120
[ 0.605004] ata6: SATA max UDMA/133 abar m2048@0x90022000 port 0x90022380 irq 120
[ 0.920369] ata3: SATA link down (SStatus 4 SControl 300)
[ 0.920386] ata2: SATA link down (SStatus 4 SControl 300)
[ 0.920402] ata1: SATA link down (SStatus 4 SControl 300)
[ 0.920419] ata5: SATA link down (SStatus 4 SControl 300)
[ 0.920434] ata6: SATA link down (SStatus 4 SControl 300)
[ 0.923702] ata4: SATA link down (SStatus 4 SControl 300)
tc@box:~$

小飞侠 发表于 2023-8-21 16:39:44

没sata驱动，或者驱动不支持，建议多试几个版本的引导测试。
也可以试一试arpl的引导制作方法。

xcgf 发表于 2023-8-21 18:11:06

插主板sata1能发现硬盘其他sata接口都不能发现硬盘

xcgf 发表于 2023-8-22 14:57:09

我在gurd.cfg 写上
SataPortMap=1
DiskIdxMap=00
硬盘查在SATA1口能识别硬盘安装。接第二块硬盘不能识别硬盘

lordghost 发表于 2023-8-24 08:51:31

你把SATA控制器改成 AHCI, 黑不支持第三方RAID卡和模式， 不能用RAID,要不你就去找网上的黑RAID卡破解兼容驱动但很麻烦，你这个就改成AHCI就马上得了

xcgf 发表于 2023-8-24 19:51:20

设置的是AHCI mode不能发现识别硬盘
页: [1]
查看完整版本: 微星主板MPG Z390 GAMING PLUS 安装群晖不能识别硬盘