QNAP的transmission安装

我的settings.json配置如下，也是不能运行，输入http://IP:9091出现：
403: Forbidden
Unauthorized IP Address.

Either disable the IP address whitelist or add your address to it.

If you're editing settings.json, see the 'rpc-whitelist' and 'rpc-whitelist-enabled' entries.

If you're still using ACLs, use a whitelist instead. See the transmission-daemon manpage for details.
明显就是IP地址认证不能通过，但我觉得没有输错呀，有谁能帮帮我，我的settings.json配置如下：
{
    "alt-speed-down": 50,
    "alt-speed-enabled": false,
    "alt-speed-time-begin": 540,
    "alt-speed-time-day": 127,
    "alt-speed-time-enabled": false,
    "alt-speed-time-end": 1020,
    "alt-speed-up": 50,
    "bind-address-ipv4": "0.0.0.0",
    "bind-address-ipv6": "::",
    "blocklist-enabled": false,
    "dht-enabled": true,
    "download-dir": "\/share\/Qdownload\/transmission\/",
    "encryption": 0,
    "lazy-bitfield-enabled": true,
    "message-level": 2,
    "open-file-limit": 32,
    "peer-limit-global": 240,
    "peer-limit-per-torrent": 60,
    "peer-port": 51413,
    "peer-port-random-high": 65535,
    "peer-port-random-low": 49152,
    "peer-port-random-on-start": false,
    "peer-socket-tos": 0,
    "pex-enabled": true,
    "port-forwarding-enabled": true,
    "preallocation": 1,
    "proxy": "",
    "proxy-auth-enabled": false,
    "proxy-auth-password": "",
    "proxy-auth-username": "",
    "proxy-enabled": false,
    "proxy-port": 80,
    "proxy-type": 0,
    "ratio-limit": 2.0000,
    "ratio-limit-enabled": false,
    "rpc-authentication-required": false,
    "rpc-bind-address": "0.0.0.0",
    "rpc-enabled": true,
    "rpc-password": "",
    "rpc-port": 9091,
    "rpc-username": "",
    "rpc-whitelist": "*.*.*.*",
    "rpc-whitelist-enabled": true,
    "speed-limit-down": 100,
    "speed-limit-down-enabled": false,
    "speed-limit-up": 100,
    "speed-limit-up-enabled": false,
    "umask": 18,
    "upload-slots-per-torrent": 14

本帖最后由 fttbcm 于 2009-12-29 09:38 编辑

哈哈终于明白了，我是看这个看懂的http://www.hkepc.com/forum/viewt ... 5086&extra=&page=33
具体说来说是在执行share/HDA_DATA/.qpkg/Optware/bin/目录下去启动Transmission时,执行下列操作：(这步很重要)
transmission-daemon -p 9091 -f -T -a *.*.*.* -w /share/HDA_DATA/Qdownload/ -g /share/HDA_DATA/Qdownload/config/
这样就行了。具体请看我的BBS:http://www.gebi1.com/viewthread.php?tid=37&extra=page%3D1

前面的操作呢，没mount好flash吧

注意#不是命令的一部分

当然也可能那个方法不适用最新版本的固件，你可以到官方论坛上去转转

mark..............

ding  ding  ding  ...  zou  ren  lo .na ji fen

11111dsfsdfsdfsdfdssfsdfsff

嗯，端口映射很重要

请问，系统的qpkg transmission好用吗？